Eloma Oven Error Codes Eloma Combi-steamer Multimax A, Multimax B, Genius T, Joker B, Joker TEloma Bake-Off Oven EB 30, EB 50, EB 80, version B and T
Eloma Oven Error Code Solutions
Access and saving of the parameter:
Access and saving of the
parameter:
1. Switch the oven on. The oven activates the steam mode automatically.
2. Adjust 3:45 with the time knob (B1) in the time display.
3. Hold the button for approx.
3 seconds. The display shows the software version for a short time. Then the display A1 shows “Pr” and
the display A2 “End”. Set all
parameters according to the table below with knob B1 (changes the parameter) and knob B2 (changes
the value of the parameter). Display A1 shows the parameter number, while display A2 shows the value of
the parameter.
4. Save your settings and leave the programming mode with the button when finished with setting.
To abort the programming switches the oven off.
| Error code | Description | Possible cause / solution | |||||
|---|---|---|---|---|---|---|---|
| 111 | Probe chamber 1 (top) No signal | Check probe 0,789mV at 20°C, replace defective probe. Shorten the terminals 11 & 12. Reset, if error still there replace the PCB Oven will NOT operate with a defective probe. | |||||
| 112 | Probe chamber 2 (bottom) No signal | Check probe 0,789mV at 20°C, replace defective probe. Shorten the terminals 13 & 14. Reset, if error still there replace the PCB Oven will NOT operate with a defective probe. | |||||
| 113 | Meat probe No signal sensor 1 | Check probe 0,789mV at 20°C, replace defective probe. Shorten the terminals 1 & 2. If error still there replace the PCB Meat probe operation is possible | |||||
| 114 | Meat probe No signal sensor 2 | Check probe 0,789mV at 20°C, replace defective probe. Shorten the terminals 1 & 4. If error still there replace the PCB Meat probe operation is possible | |||||
| 115 | Meat probe No signal sensor 3 | Check probe 0,789mV at 20°C, replace defective probe. Shorten the terminals 1 & 6. If error still there replace the PCB Meat probe operation is possible | |||||
| 116 | Meat probe No signal sensor 4 | Check probe 0,789mV at 20°C, replace defective probe. Shorten the terminals 1 & 8. If error still there replace the PCB Meat probe operation is possible | |||||
| 113 114 115 116 | Meat probe No signal off all 4 sensors | The common wire is defective, change the probe. Meat probe operation is NOT possible | |||||
| 117 | Probe waste water (drain) No signal | Check probe 0,789mV at 20°C, replace defective probe. Shorten the terminals 15 & 16. If error still there replace the PCB Oven will operate with a defective probe. | |||||
| 127 | Probe waste water (drain) {Genius/Genius-T only} | Follows error 117: Value for temperature is not correct. Oven will operate with a defective probe. | |||||
7. Switch the oven on and activate the “manual Input”.
8. Using the arrow buttons, set the curser to a temperature of 200 °C and 0% humidity, confirm by
pressing the “OK”.
9. Using the arrow buttons, set the time to 3:45.
10. By pressing the right function button “Active Temp Off” the service menu is activated.
11. Adjust the settings according to the following data sheet for: Unit parameters Unit function
Gas settings (only Gas models)
12. By pressing the button “OK“, the settings are saved.
| Error code | Description | Possible cause / solution | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 211 | Upper safety thermal release | Reset the upper safety thermal release. Check the fuse F1 (8 Amps slow) on PCB. If the STR has not released, check if the motor temperature sensor switched of, this is a bi-metal trip, which resets itself when cooled down. If so, control the main/motor fuses. Replace and check possible causes: Defective motor windings or the motor is blocked. Is the contact 13/14 of main contactor K1/Q1 closed? Or check X10, pin 1/2. This is a security loop; if this loop is open the contactor goes off after a few seconds. If this error occurs a couple of times it is likely that a motor contactor or the main-contactor has a bad contact, in this case replace the contactor. Oven cannot operate! | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 212 | Lower safety thermal release | Reset the lower safety thermal release. Check the fuse F1 (8 Amps slow) on PCB. If the STR has not released, check if the motor temperature sensor switched of, this is a bi-metal trip, which reset itself when cooled down. If so, control if the main/motor fuses. Replace and check possible causes: Defective motor windings or the motor is blocked. Is the contact 13 / 14 of main contactor K2/Q2 closed? Or check X10, pin 3/4.This is a security loop; if this loop is open the contactor goes off after a few seconds. Oven cannot operate | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 1 | Door open | Close the door / operating panel. Check the door switch, inside the operating panel. You may check this by shorting the terminal 9 & 10 at X10. Is the magnet lost (Inside the door frame)? | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 2 | Emergency opening door | Door was opened with the emergency opening. Check closure mechanism. Oven can’t operate! | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 3 | Door switch | Micro switch of door from motor not activated. Micro switch is loose. Oven can’t operate! | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 4 | Door not closed | Door hook defective. Magnet switch faulty. Oven can’t operate! | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 5 | Door motor works permanently | Door can’t get closed. Oven can’t operate! | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 6 | Door not in position | No defined position. Oven can’t operate! | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 311 | No water / low water pressure | Open the water tap. The water flow pressure must be checked, 2 bar / 29 PSI for soft water. Check the water pressure switch, terminal 11 & 12. Autoclean will pause until pressure is high enough. | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 312 | Not enough water | Is the appliance connected to water? Check if water tap is open. Control the flow water pressure Adjust the solenoid valve to the correct amount of water. See table “Table 1.2.2”. Refer 2.3.1 No steam | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 313 | Hand shower | Hand shower is not working; only Joker models! | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 314 | Fill level tank | Water tank is empty. Only EB30 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 315 | Water flow w/o request | Water flows into the cavity but not required by program/user. Only EB 30 B/T and XL Oven cannot operate! | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 711 | No flame upper chamber | Is the phase at L1, polarity! Is the kitchen ventilation system working? Interlock? Check the ionisation current of the gas firing (Part A4 pin J5, older version X3) Reset: Pressing restart. Refer 2.6.2 Restart Gas | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 712 | No flame lower chamber | Is the phase at L1, polarity! Is the kitchen ventilation system working? Interlock? Check the ionisation current of the gas firing (Part A4 pin J5, older version X3) Reset: Pressing restart. | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Error code | Description | Possible cause / solution | |||||
|---|---|---|---|---|---|---|---|
| 111 | Probe chamber 1 (top) No signal | Check probe 0,789mV at 20°C, replace defective probe. Shorten the terminals 11 & 12. Reset, if error still there replace the PCB Oven will NOT operate with a defective probe. | |||||
| 112 | Probe chamber 2 (bottom) No signal | Check probe 0,789mV at 20°C, replace defective probe. Shorten the terminals 13 & 14. Reset, if error still there replace the PCB Oven will NOT operate with a defective probe. | |||||
| 113 | Meat probe No signal sensor 1 | Check probe 0,789mV at 20°C, replace defective probe. Shorten the terminals 1 & 2. If error still there replace the PCB Meat probe operation is possible | |||||
| 114 | Meat probe No signal sensor 2 | Check probe 0,789mV at 20°C, replace defective probe. Shorten the terminals 1 & 4. If error still there replace the PCB Meat probe operation is possible | |||||
| 115 | Meat probe No signal sensor 3 | Check probe 0,789mV at 20°C, replace defective probe. Shorten the terminals 1 & 6. If error still there replace the PCB Meat probe operation is possible | |||||
| 116 | Meat probe No signal sensor 4 | Check probe 0,789mV at 20°C, replace defective probe. Shorten the terminals 1 & 8. If error still there replace the PCB Meat probe operation is possible | |||||
| 113 114 115 116 | Meat probe No signal off all 4 sensors | The common wire is defective, change the probe. Meat probe operation is NOT possible | |||||
| 117 | Probe waste water (drain) No signal | Check probe 0,789mV at 20°C, replace defective probe. Shorten the terminals 15 & 16. If error still there replace the PCB Oven will operate with a defective probe. | |||||
| 127 | Probe waste water (drain) {Genius/Genius-T only} | Follows error 117: Value for temperature is not correct. Oven will operate with a defective probe. | |||||
| Error code | Description | Possible cause / solution | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 511 | Pre-warning: PCB temperature 65°C | Clean air filter, located at the bottom of the front panel. Check if the compartment fan and the fan in the front panel are working. See chapter 2.2.4 Oven can operate! | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 512 | Warning: PCB temperature 70°C | Clean air filter, located at the bottom of the front panel. Check if the compartment fan and the fan in the front panel are working. See chapter 2.2.4 Oven switches off! | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 0 513 | Warning: PCB temperature 68°C | Slow overheated PCB. The installation prevents ambient air flow for a cooling effect. | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| AC | Breaking off Autoclean | Press start, the oven will operate the flushing mode. Message comes up after breaking off the Autoclean cycle or interrupting the power supply. | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||