Vestel Dishwasher Error Codes

Dishwasher, Error Codes, Vestel 3,410 Views

Vestel Dishwasher Error Codes When you see an abnormal problem on your device, you can use this guide to identify the cause of the problem and find a solution on your own.

Vestel Dishwasher Error Code Solutions

Fault CodePossible FailureSolution
F5Insufficient water intake.
  • Make sure that the water inlet tap is completely open and that the water is not cut off.
  • Close the water inlet tap, separate the water inlet hose from the tap and clean the filter at the connection end of the hose.
  • Restart your machine, if the error persists, contact the service.
F3Continuous water intake error
  • Turn off the faucet.
  • Contact the service.
F2The machine cannot discharge wastewater.
  • The water drain hose may be clogged.
  • The filters of your machine may be clogged.
  • Turn your machine off and on and activate the program cancel command.
  • If the error persists, contact the service.
F8Heater error
  • Contact the service.
F1Overflow alarm active
  • Turn off your machine and the faucet.
  • Contact the service.
F7Overheating error (temperature inside the machine is too high)
  • Contact the service.
F9divisor position error
  • Contact the service.
F6Temperature sensor faulty
  • Contact the service.
FEElectronic card parameter recognition error
  • As a result of very sudden and continuous voltage drops, the electronic board cannot keep the software variables in memory.
  • The program will resume when run again. Mains voltage should be checked.

PROBLEM SOLUTIONS

Cause enumeration is mapped to Remedy enumerations.

PROBLEMREASONSOLUTION
The program does not start.
  1. Power cut. –>
  2. The on/off button is not turned on. –>
  3. The fuse is blown. –>
  4. The plug is not plugged in. –>
  5. The machine door is open. –>
  6. The water inlet tap is closed. –>
  7. Water inlet and machine filters are clogged. –>
  1. Wait for the power to come on.
  2. Turn on your dishwasher.
  3. Have the fuse replaced.
  4. Plug in.
  5. Close the machine door.
  6. Open the water inlet faucet.
  7. Clean the water inlet and machine filters.
After the program ends, water remains in the machine.
  1. The water drain hose is clogged or kinked. –>
  2. The filters are clogged. –>
  3. The program has not yet ended. –>
  1. Clean the clogging materials and restart your machine.
  2. Clean the clogging materials and restart your machine.
  3. Wait for the program to finish.
There are vibration and crashing sounds during washing.
  1. The dishes are not placed correctly. –>
  2. The propeller hits the dishes. –>
  3. The propellers may not be installed. –>
  1. Load the dishes correctly.
  2. Load the dishes correctly.
  3. Install the propellers.
Some food residues remain on the dishes.
  1. The sprayed water did not reach the relevant places. –>
  2. The dishes are leaning against each other. –>
  3. The dishwasher basket is overfilled. –>
  4. Filters are clogged –>
  5. Filters installed incorrectly. –>
  6. The drain pump may be clogged. –>
  7. Too little detergent has been added. –>
  8. Unsuitable detergentused. –>
  9. Spray arm is clogged with food residue. –>
  10. An unsuitable weakwashing program has been selected. –>
  1. Place your dishes properly so that they do not interfere with each other.
  2. Place your dishes properly, empty your excess dishes from your appliance.
  3. Clean and open the filters.
  4. Install the filters correctly.
  5. Call service.
  6. Add the amount of detergent specified in the manual.
  7. Change your detergent brand.
  8. Clean the spray arm.
  9. Select the program that is suitable for your access from the program breakdown section in your guide.
The machine stops during washing.
  1. The electricity has been cut. –>
  2. The program may be in standby mode. –>
  3. Problem with water inlet. –>
  1. Wait for the electricity to come.
  2. Bring the program from standby to running.
  3. Check if the water hose is clogged, and if it is, remove the blockage.
There are whitish spots on the dishes.
  1. Very little detergent is used. –>
  2. The rinse aid setting is too small. –>
  3. Although the water hardness levelis high, no special saltis used. –>
  4. The salt container lid is notclosed properly. –>
  1. Bring the amount of detergent to therequired level.
  2. Increase the rinse aid setting.
  3. Put the special salt produced for your dishwasher into your machine.
  4. Close the lid of the salt compartment well. Make sure that it is closed properly.
The dishes are not drying.
  1. A program without drying processhas been selected. –>
  2. The rinse aid dosage isset too low. –>
  1. Select a program with a drying step by examining theprogram casting page from your user manual .
  2. Increase the rinse aid setting.
There are traces of rust on the dishes
  • Mains groundingis not healthy. –>
  • The stainless steel quality of the dishes washed is insufficient. –>
  • The salt content of the washing water ishigh. –>
  • The salt compartment lid is not properly closed. –>
  • While filling the salt, too much salt may have spilled tothe sides, into the machine .–>
  1. Have your mains groundingchecked by an electrician.
  2. Make sure that the steel quality of the tools you use in the dishwasher is appropriate.
  3. Decrease the salt adjustment value.
  4. Close the lid of the salt compartment well. Make sure that it is closed properly.
  5. When filling salt, be careful that it does not overflow to the sides, if it overflows, wipe it with a cloth to clean the overflowing salt.

One comment

  1. Hassan
    at

    My Vestle dishwasher, starts and then stops and shows error code FF

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *

Designed by Erol Uzunoglu