How to Replace Oven Thermostat ? Your oven thermostat is very important; it is responsible for ensuring that your oven heats up to the set temperature and that it remains regulated at all times. That’s why it’s important to know how to replace your oven thermostat if you find it is no longer working.
Oven Thermostat Replacement
The thermostat control sits behind the temperature control knob; with a capillary tube that then runs around the back of the oven to the top of the oven cavity.
Before we go any further, let’s just make sure you are on the right path – here are the warning signs that your oven thermostat is broken.
- The temperature inside the oven is not reaching what you’ve set it to on the temperature knob and the temperature indicator light is going off before reaching the correct temperature.
- The temperature inside the oven is always at maximum, no matter what you’ve got it set to.
- If you’re not hearing the tell-tale click when you turn the control knob.
If you need to replace the thermostat in your oven, then you will be pleased to know that you have come to the right place! If you are unsure where to start there’s no need to panic. We’ll talk you through how to successfully replace the thermostat without damaging your oven.
Repairing the Oven Setting Control
When the oven setting control malfunctions, the oven won’t heat. Here’s how to repair an oven setting control:
Step 1: Remove the control knob.
Step 2: Remove the back service panel or the front panel, if necessary. Remove other control knobs as needed to remove the panel. The oven setting control is located directly in back of the control knob and is usually held to the control panel by two screws.
Step 3: Testing the control with a volt-ohm-milliammeter (VOM) is not recommended, because the results will not always be conclusive. If you suspect that the setting control is faulty, the best procedure is to substitute a control that you know is working, or you could simply replace the faulty control with a new one made for the oven.
Step 4: Disconnect the electrical lead wires from the control terminal and lift out the control. Connect the new control the same way the old one was connected.
Servicing Oven Thermostats
If the oven doesn’t heat evenly or doesn’t heat at all, the oven thermostat may be malfunctioning. First, determine how much the temperature in the oven is off from the control setting. To do this, put an oven thermometer on a center rack inside the oven and turn the oven on for about 20 minutes, with the thermostat set at any range between 300 degrees and 400 degrees Farenheit. If the oven thermometer reads 25 degrees or more lower or higher than the oven control setting, the thermostat should be recalibrated. Here’s how to calibrate the thermostat:
How to Replace Oven Thermostat ?
Step 1: Pull off the thermostat knob on the control panel. Behind the knob are two screws holding a round, notched plate. Loosen these screws, but do not remove them.
Step 2: With a screwdriver, change the notch setting on the notched plate by turning the plate counterclockwise; for every eighth of a turn, the oven temperature goes up about 25 degrees Farenheit. To turn the heat down, turn the plate clockwise.
Some thermostats can be adjusted by turning a screw inside the control knob shaft housing. To do so, remove the knob and insert a screwdriver into the shaft so that the screwdriver blade engages a screw slot. Turn the screwdriver counterclockwise about one-eighth of a turn to raise the heat about 25 degrees Farenheit. Here’s how to test a malfunctioning thermostat:
Step 1: Test the thermostat with a VOM (multimeter) set to the RX1 scale. The thermostat is located directly on the back of the control knob that regulates the heat. To gain access to the thermostat, remove the back service panel to the control panel.
Step 2: Disconnect one electrical lead wire from a terminal of the thermostat and clip one probe of the VOM to each thermostat terminal. If the thermostat is in working order, the meter will register zero. If the needle jumps to a higher reading, the thermostat is faulty and should be replaced.
Step 3: If necessary, replace the thermostat with a new one of the same type.
If you need to replace the thermostat, follow these guidlines:
Step 1: Disconnect the terminal wires to the thermostat and pull off the control knob.
Step 2: Remove the retaining screws. On some ranges, there is a wire running from the thermostat into the oven. This wire operates a sensing bulb that controls the thermostat. The sensing bulb is usually held by a bracket; unscrew this bracket to remove the bulb. Then carefully slip out the wire, the bulb, and the thermostat.
Step 3: Install the new thermostat using a reverse procedure.