Electrolux Dishwasher Error Codes The complete error code will be stored among the three errors that can be stored by the appliance. A new error code is only stored if it differs from the last one stored. The three most recent error codes can be displayed only in Service Mode or using the Sidekick tool. Only the error family codes are displayed to the user. The complete error codes are displayed in Service Mode. Appliances with a display will show the complete error codes as above format.
Electrolux Dishwasher Error Code Solutions
|Low mains voltage
|Water Tap Closed
|During dynamic filling
|Water detected from aqua control sensor
|Analogue pressure sensor problem
|No pressure sensor signal
|Calibration invalid, pressure signal too noisy
|Pressure sensor signal too high
|Pressure sensor signal too low
|Calibration invalid, pressure signal too low
|Calibration invalid, pressure signal too high
|Washing Motor Problem
|Asynchronous motor problem
|WP BLDC motor – abnormal high current detected
|WP BLDC motor – over current
|WP will not follow/ rotor is locked
|DC Link overvoltage
|DC Link under voltage
|MCB Vbat voltage plausibility / ADC Fault
|WP motor plug connection
|WP current read ADC – fault
|Over temperature or Overload
|WP/DP current plausibility
|DP BLDC motor – abnormal high current detected
|DP BLDC motor – high current SW
|DP will not follow/ rotor is locked
|DP motor plug connection
|Heating Element Problem
|Heating over temperature
|Thermistor problem. NTC sensor value out of range
|Auto door opener malfunction
|Auto door opener warning
|Checksum CCF. The error is signalled if the configuration control of the washing cycles provided erroneous results.
|Checksum UIDATA. The error is signalled if the configuration control of the UI configuration data provided erroneous results.
|UIDATA version mismatch. The error is signalled if the UIDATA provided in configuration file mismatches the attached UI board.
|UIDATA checksum mismatch. The error is signalled if the UIDATA checksum type provided in configuration file mismatches with the attached UI board.
|Sensor Problem. Turbidity sensor. The error is set if the calibration procedure is not completed after 15 sec. The washing program will run as though the dirt value to be considered is high.
|Communication Problem. User interface communication. The error signal is displayed if the communication system does not recognize any display board.
|MACS bus communication. After three attempts to establish communication, an error is signalled in the hardware control.
|ADSI communication. The washing programme is suspended but it can be restarted if the error conditions no longer apply.
|Communication between the power board and the Motor Control Board.
|Tacho Problem. No signal. The error is stored and displayed only in service mode; there is a new control for each new phase. If the washing pump is activated but there is no tacho signal for 30 seconds then the motor speed is set to full speed and the heating element is not activated.
|Critical signal. The error is stored and displayed only in service mode. If the washing pump is activated but there is no tacho signal for 5 seconds then the heating element is temporarily deactivated. If after another 30 seconds there is still no signal the appliance displays an error code iD0.
|Flow control position (spray arm level)
|Water level problem. Overfilling detected.
|High water level
|The appliance does not fill with water
|The appliance does not drain the water
|The anti-flood device is on
Electrolux Dishwasher Care And Cleaning
To remove and clean the filters
Dirty filters decrease the washing results. Although the maintenance is very low with these filters, make a check at intervals and if necessary, clean them.
- Turn the filter (A) counterclockwise and remove it out from filter (B).
- Filter (A) has two parts. To disassemble the filter, pull them apart.
- Fully clean the parts with water.
- Put the two parts of the filter (A) together and push. Make sure that they engage correctly in each other.
- Remove the filter (B).
- Fully clean the filter (B) with water.
- Put the filter (B) to its initial position. Make sure that it engages correctly in the two guides (C).
- Put the filter (A) into position in filter (B). Turn the filter (A) clockwise until it locks.
Electrolux Dishwasher Troubleshooting
|The appliance does not fill with water.
|The water tap is blocked or there is limescale on it. Clean the water tap.
|The water pressure is too low. Contact your local water authority.
|The water tap is closed. Open the water tap.
|The filter in the water inlet hose is blocked. Clean the filter.
|The connection of the water inlet hose is not correct. Make sure that the connection is correct.
|The water inlet hose is damaged. Make sure that the water inlet hose has no damages.
|The appliance does not drain the water.
|There is a blockage in the sink spigot. Clean the sink spigot.
|The connection of the water drain hose is not correct. Make sure that the connection is correct.
|The water drain hose is damaged. Make sure that the water drain hose has no damages.
|The anti-flood device is on.
|Close the water tap and contact the service centre.
|The start of the washing programme does not occur.
|The appliance door is open. Close the appliance door.
|The mains plug is not connected in the mains socket. Connect the mains plug.
|The fuse in the fuse box is damaged. Replace the fuse.
|The delay start is set. Cancel the delay start. When the countdown is completed, the washing programme starts automatically.
|The dishes are not clean.
|The washing programme was not applicable for the type of load and soil. Make sure that the washing programme is applicable for the type of load and soil.
|You did not put the items correctly in the baskets, water did not touch all surfaces. Put the items correctly in the baskets.
|The spray arms could not turn freely. Incorrect position of the items in the baskets. Make sure that an incorrect position of the items do not cause the blockage of the spray arms.
|The filters are dirty or not assembled and installed correctly. Make sure that the filters are clean and correctly assembled and installed.
|The quantity of detergent was not sufficient or missing. Make sure that the quantity of detergent is sufficient.
|Limescale particles on the dishes.
|The salt container is empty. Fill the salt container with dishwasher salt.
|Incorrect level of the water softener adjustment. Adjust the water softener with the correct level.
|The salt container cap is not closed correctly. Make sure that the salt container cap is closed correctly.
|There are streaks, whitish stains, or a bluish layer on glasses and dishes.
|The rinse aid quantity is too high. Decrease the rinse aid quantity.
|Dry water drop stains on glasses and dishes.
|The rinse aid quantity is too low. Increase the rinse aid quantity.
|The dishes are wet.
|The washing programme was without a drying phase or with a decreased drying phase. For better drying results, keep the door ajar for some minutes.
|The dishes are wet and matt.
|The rinse aid dispenser is empty. Fill the rinse aid dispenser with rinse aid.
|The multitab function is on (this function automatically deactivates the rinse aid dispenser). Activate the rinse aid dispenser.