AEG Refrigerator Error Codes

AEG Refrigerator Error Codes This guide contains everything you’ll need to figure out what error your AEG Fridge is trying to communicate. Whether it’s a noisy fridge, a smelly fridge, or your fridge is too hot. Remember to call an engineer if you’re not able to fix it yourself, and check the common issues below the table for some other useful information. For other valuable articles, check out the rest of our helpdesk articles here.

AEG Refrigerator Error Code Solutions

Error CodesSolution
E0No error
E1Evaporator sensor damaged
E2Room temperature sensor damaged (installed on the display board)
E4Room temperature sensor damaged (installed on the power board)
E50 degree compartment sensor damaged
Erhttp://IM/RAM Error. Check J4-4, J4-5 and J4-6 Connector on Icemaker board. Check J4 connector at Main Control board. Check 15 pin inline connector at control board, Pin#’s 4,9 & 14. If all connections test good, control board.
t3TH3 Sensor (open or short) Go to flow chart for Ice t3
CEIM Com Lost Go to flow chart 50C. Put into service mode to verify.
SY – EFEvaporator Fan Failure
SY – CECommunication Error
SY – CFCommunication Failure
F7It might be that the power supply has been interrupted for a period or that the door has been too long or not properly closed.
F2It is possibly a faulty thermostat.
AEG Refrigerator Parts

AEG Refrigerator Troubleshooting

A malfunction may be caused by only a minor fault that you can rectify yourself using the following instructions. Do not perform any other work on the appliance if the following information does not provide assistance in your specific case.

Important! Repairs to refrigerators/freezers may only be performed by competent service engineers. Improper repairs can give rise to significant hazards for the user. If your appliance needs repairing, please contact your specialist dealer or your local Service Force Centre.

TroublePossible Cause-Remedy
Appliance does not work.Appliance is not switched on. Switch on the appliance.
Mains plug is not plugged in or is loose. Insert mains plug.Fuse has blown or is defective. Check fuse, replace if necessary.Fuse has blown or is defective. Check fuse, replace if necessary.
Fuse has blown or is defective. Check fuse, replace if necessary.
Socket is defective. Mains malfunctions are to be corrected by a qualified electrician.
The compressor runs continuously.Temperature is set too cold. Set the Electronic Control to a warmer setting temporarily.
The food is too warm.Temperature is not properly adjusted. Please look in the “Starting Up and Temperature Regulation” section.
Door was open for an extended period. Do not leave the door open any longer than necessary.
A large quantity of warm food was placed in the appliance within the last 24 hours. Set the Electronic Control to a colder setting temporarily.
The appliance is near a heat source. Please look in the“Installation location” section.
Interior lighting does not work.Light bulb is defective. Please look in the “Changing the Light Bulb” section.
Heavy build up of frost, possibly also on the door seal.Door seal is not airtight (possibly after reversing the door). Carefully warm the leaking sections of the door seal with a hair dryer (on a cool setting). At the sametime shape the warmed door seal by hand such that it sits correctly.
Unusual noises.Appliance is not level. Readjust the feet.
The appliance is touching the wall or other objects. Move the appliances lightly.
The compressor does not start immediately after changing the temperature setting.This is normal, no error has occurred. The compressor starts after a period of time.
Water in the bottom of the cabinet.Water drain hole is blocked. See the “Cleaning and Care” section.


The warning signals of the control and signalling system of the appliance are displayed on the visual display. The system will give out a signal if:  An error has occurred in the operation of the appliance. In case the electronic system of the appliance cannot identify the real temperature, one of the following signs will appear on the temperature display: Until the product is repaired, the appliance will continue to run on a standby program to protect the food stored within.

Cleaning and Care

For hygienic reasons the appliance interior, including interior accessories, should be cleaned regularly.

  • The appliance must not be connected to the mains during cleaning. Danger of electrical shock. Before cleaning switch the appliance off and remove the plug from the mains, or switch off or disconnect from the electricity supply.
  • Never clean the appliance with a steam cleaner. Moisture could accumulate in electrical components and there is a danger of an electrical shock. Hot vapours can lead to the damage of plastic parts.
  • The appliance must be dry before it is switched back on.

Leave a Reply

Your email address will not be published. Required fields are marked *