Electrolux Induction Cooker Error Codes While using these cooktops, you will notice that there is a control panel present that you can use to control the device. In case of any problems, the error codes will be shown here.
Electrolux Induction Cooktop Error Code Solutions
The best thing about these is that your issues are narrowed down and you can then easily fix the problem you were getting. This takes out all the worry of having to pinpoint problems on your cooktops. The error code 2 refers to the left front element down key being defective.
Aside from this, the error codes 3 and 4 also refer to the same issue but 3 means that the up key is defective while 4 refers to the on and off-key. Considering this, all of these codes refer to the same touch control board so you can use the same fix for each of them.
The first thing that can be done is to check the wirings. These might have come off or gotten loose. If you notice this then simply connecting the cable back tightly should fix the problem you were getting.
On the other hand, in some cases, the touch control unit can also become damaged. If this happens then you will have to get it entirely replaced. Even if only a single button is broken, you will still have to replace the entire touchpad. This is why make sure that you try checking the wires carefully.
You can even use a voltmeter to help you in identifying if the cables are getting current flowing through them. If you do not know how these can be checked then a better option is to contact a specialist.
- Error Code 30
All the error codes after the ones mentioned above refer to different buttons on the touchpad being defective. Although, there are several elements which is why there are so many codes for them. You can consult the manual to help you with understanding what key the code is referring to. Other than that, the fix for all of these will be the same.
As for the error code 30, this refers to the power supply not getting enough current or there being an electrical issue. You can take off your cooktop from the main power for this and then check the current coming from the backend.
You must use a voltmeter for this as getting accurate readings is important. If the issue was true with the socket then get it replaced. If not then you will have to ask an electrician to check the power supply unit or send in your device for repairs.
- Error Codes 51 to 54
The error codes 51 to 54 all refer to their being issues with the temperature sensors on your Electrolux induction cooktop. Considering this, you will have to disconnect your device from the main power first. You can then test the resistance on your sensors using an ohmmeter.
Sometimes cleaning off all the dust that was stuck on the sensors can help in fixing them. Although, make sure that you do not apply too much force. This is because the sensors are quite sensitive and can get damaged easily. If these have broken down then you will have to get them replaced. Contact the company for this as well as using third-party sensors can be dangerous on cooktops like these.
Error code | Description | Causes and solution |
---|---|---|
L | The “Child Protection” mode is active. | To deactivate child protection, press and hold the lock key for a few seconds until a beep sounds. |
F | Use of unsuitable cookware on the cooking zone. | There can be several reasons: a round or ribbed bottom (as a result, an air cushion is formed). Or you took a pot / frying pan without a ferromagnetic coating, which is also prohibited. |
E1 | The temperature of the electronics module has been exceeded. | Most often, a breakdown is provoked by a short circuit of the module, Contact burnout is another reason. Contact service to replace defective components and electronics. |
E3 | Lost communication with inverter. | The malfunction occurs due to an interruption in the circuit or errors in the installation of the hob. It is necessary to contact customer service to troubleshoot / replace the inverter. |
E4 | Overheating of burners. | Most likely you cook at the highest power. The cooling element and ventilation can not cope. Reduce the heating intensity of the burner or switch off until completely cooled. |
E5 | No network contact | Check the line voltage; it may be too low or high. Reboot the device. The power cable may often be pinched or damaged. |
E6 | Communication with the power inverter is interrupted. | In this case, the contacts on the block or the inverter itself burned out. It is impossible to fix the breakdown yourself. To install serviceable contacts or a unit, you must contact service. |
E7 | The cooling fan is blocked or broken. | Turn on the large hotplate for a minute and turn it on. Try to clean the fan. If cleaning does not give the desired result, contact the service to replace it. |
E8 | There is no communication between the power inverter and the display unit. | You need to install a new central connector on the brewing unit. There may be problems in the touch panel itself. Call the wizard from the service center. |
E9 | Faulty electronics. | The cause of the breakdown could be a circuit in the network or a marriage, oxidation of contacts. A complete replacement of the electronics module is required, contact a service center. |